Use Instructions

Before using the product, please read this manual fully to understand the correct and safe operation method.

The use of this product represents that you have fully read and agreed to the terms and safety matters in this manual.

Fuber is not responsible for any property damage or personal injury caused by operations not complying with the provisions of this manual.

Use The Legend

When reading this manual, please refer to the following figure legends:

(1) ⚠️ Important instructions or warnings

(2) 💡 Tips or tricks for use

01 / Product Instruction

⚠️ warning:

To avoid product losses caused by improper operation, please read all the operation instructions and safety information in this manual first, and then use FUBER products.

For more product information, please log in to: https://www.fuberpropulsion.com/ for inquiries.

1、The display screen shows real-time operation information.

2、The emergency safety switch ensures safety.

3、The rudder lever type throttle operates smoothly.

4、Battery level alarm reminder.

5、Deep-sea grade anti-corrosion coating.

6、Built-in GPS positioning.

02/ Installation Instructions

Must-read before installation.

⚠️ Important instructions or warnings

a. Avoid battery short circuit when connecting.

b. Once the power cable or communication cable is interrupted, the outboard motor will stop working.

💡 Tips or tricks for use

a. When installing, ensure that the connector is dry to prevent short circuits.

b. Please clean the connection connector once every three months.

c. During use, if poor contact is found, it is recommended to check the connection and fastening of each terminal.

💡 Tips or tricks for use

1. Please be sure to fix this product on the central axis of the ship. If your ship is asymmetrically designed, please consult an authorized dealer of Fuber Technology to adjust the appropriate installation position.

2. For long-term continuous use, it is recommended to use bolts to connect the equipment from the spare fixing holes to the hull to enhance the locking effect.

02/ Installation Instructions

Front control / Stern control

Step ①

Hang the product on the hanging plate at the stern of the boat for fixing the outboard, and rotate the locking clamp handle.

Step ② Front control version

Label annotations in diagram：

· Power cable

· Control box

· Communication cable

Text description:

For the female end of the waterproof connector of the power cable, plug it into the male end of the power connector at the handle end of the product and rotate to lock it (refer to the picture below).

Connect both ends of the communication cable to the product and the control box respectively.

Step ② Stern control version

Label annotations in diagram：

· female

· male

Text description:

For the female end of the waterproof connector of the power cable, plug it into the male end of the power connector at the handle end of the product and rotate to lock it.

02/ Installation Instructions — Pod

Wiring Connector Diagram Annotation

General Note

Note: The flatness requirement of the ship board is 0.1mm and the roughness is 3.2μm.

Step ①

Component labels：clamping ring、Pod gasket、bottom flange of ship

Description text：

Place the pod gasket on the bottom flange of the ship and press it close to the ship plate. Then, press the bottom surfaces of the left and right clamping rings against the ship plate and lock them.

Step ②

Component & screw labels：top flange of ship、bottom flange of ship、exhibition board、6 - M5×35 screws、2 - M10×30 screws

Description text：

Finally, lock the screws on the top flange and the bottom flange of the ship. The thickness of the exhibition board is 4mm.

If the thickness of the ship plate is increased, the length of the six screws should also be increased accordingly.

Step ③

Component labels：Female end of wiring harness (Figure 1)、communication cable、Male end of control box (Figure 2)

Description text：

Plug and connect the female end of the aviation connector with the male end of the anti-reverse connection connector and rotate to lock it. Connect both ends of the communication cable to the anti-reverse connection box and the control box respectively.

Connect the Anderson connector on the other side of the anti-reverse connection to the power supply, and then it can be used.

Pod Drilling holes in the ship board