03 / Start Operation Instructions

Must-read before operation

Please check the following items before startup:

a. Confirm whether the propeller is locked.

b. Ensure that the product is completely locked to the stern plate and in the correct position.

c. Please confirm whether the magnetic safety buckle is in the handle placement position.

d. Check and confirm whether the battery installation slot is fixed (Chapter 08).

e. Check and confirm whether the handle connecting rod is tightened.

f. Check whether the throttle handle can rotate smoothly.

g. Examine whether all connections are in good condition and free from aging.

h. Inspect whether the power connection part is dry to avoid short circuits.

⚠️

a. When starting the machine, people must keep away from the propeller area to avoid getting scratched.

b. Before connecting the power cord, make sure it is dry.

c. For safety consideration. please connect the lanyard of the magnetic safety buckle to your wrist or clothing throughout the process.

d. Please note the magnetic field of the magnetic safety buckle. Keep it away (about 50 cm) from magnetically sensitive items such as regulators and medical devices.

e. Please keep the magnetic safety buckle away from electronic products that are susceptible to interference.

f. Please keep the magnetic safety buckle away (about 50 cm) from valuable items sensitive to magnetism, such as magnetic cards.

03 / Start Operation Instructions

Stern control

Operation Steps

1. Place the magnetic safety buckle in the position shown in the figure.

2. Fasten the lanyard of the magnetic safety buckle to the operator's wrist or their clothing.

3. Turn the throttle handle to start the machine.Meanwhile, you can control forward movement (turn left) or backward movement (turn right).

1. OK button: long press to turn on the machine when it is stopped, long press to turn off the machine when it is turned on; short press to refresh the screen display immediately.

2. After pressing the "+" button, press the "-" button (more than 10 seconds) to calibrate the handle.

3. Press the SET button (more than 10 seconds) to clear the alarm.

03 / Start Operation Instructions

Front control

Supplementary note

(The current screen shows dual - drive for both the left and right sides. When in single - drive mode, only the value of one side is displayed.)

1. Place the magnetic safety buckle in the position shown in the figure.

2. Fasten the cord of the magnetic safety buckle to the operator's wrist or the clothing they are wearing.

3. Press the "ON/OFF" button to turn on the machine.

4. After the control box is turned on and started, slowly push the throttle to the forward or backward position and increase the throttle power in between.

Before starting the control box, please return the throttle to the zero position.

When directly turning the throttle from the forward position to the backward position, the outboard motor will first stop running briefly and then rotate in the opposite direction.

04 / Shutdown Operation Instructions

1. Turn the throttle handle to the N (Neutral) position.

2. Unplug the magnetic safety buckle.

3. Unplug the power cable.

1. Push the throttle handle to the zero position.

2. Unplug the magnetic safety buckle.

3. Press the "ON/OFF" button to turn off the device.

⚠️ In an emergency situation,such as falling into the water,the safety switch can be directly pulled out to stop the machine.

05 / Operating Instructions For Raising The Fuselage

1. The product can adjust the tilt angle in the following ways:

a. Pull the caliper paddle upwards.

b. Then, press down the throttle handle and the fuselage can tilt up.

Warning

a. Only when the outboard motor is stopped can the tilt angle be adjusted.

b. During the process of adjusting the angle, please operate slowly when tilting up and down to avoid collision damage to people or the machine.

c. When testing the working condition of the tilt angle, please increase the speed slowly and observe the water flow at the stern at any time.

If the water flow is abnormal (such as cavitation of water flow, etc.), please stop the machine immediately and reduce the pitch angle.

2. Solution

a. When adjusting the fuselage angle, rotate the locking handle to the unlocked position. Then, the fuselage angle can be adjusted according to actual needs (the adjustable degrees are 7°、14°、21°、65°).

b. In the normal no-load state, generally select the 0° position according to the ship type. Select the 73° position in the case of stopping and docking. After loading, the other angles can be adjusted according to the driving situation to achieve the optimal speed.

💡Equipment caliper. The opening size is as follows.

Please ensure the size of the boat transom:

a. The thickness should be less than 58mm to avoid the caliper not being able to be placed properly.

b. The height should be not less than 70mm to avoid being unable to tighten the clamp handle.